DELTA

Facility Specifications

  • Accredited and non-accredited regulatory compliance testing, within
    - EMC, EMF
    - Reliability – climatic test – mechanical test
    - Acoustics, noise and vibrations Acoustics
  • Climatic tests
    - Test of mechanical, electronic and electro mechanical products. Simulate product environment to make sure that product meets the conditions to which it will be exposed to during use.       
        - High temperature
         - Low temperature
        - Constant moisture
        - Cyclic moisture
        - Thermal shock
        - Icing

  • Climatic testing equipment
    - Temperature and moisture chambers: 1-50m3, -100°C to +250°C, 20% RH to 98% RH 
    - Temperature variation from -100°C to +200°C, 5°C/min, though 60°C/min in the HALT or 2   chamber method 
    - Thermal vacuum chamber: 1m3, -40°C to +85°C, atmospheric pressure down to better than 1.3 x 10-3 Pa 
    - Salt fog chamber: +30°C to +40°C, 98% RH, typically 5% NaCl 
    - Dust chamber, free-settling dust, typically 6g/(day/m2) 
    - Artificial sun (UV simulation)
    - Corrosion chambers: SO2, H2S 
    - Water seal, all IP classes and high pressure testing 
    - Dust tests with/without vacuum, IP 5X and IP 6X 
    - Dust test with free-settling dust
    - Combined vibration and temperature: -70°C to +180°C 
    - HALT: -100°C to +200°C, 60°C/min, 70 grms (6-axes vibration)
  • Mechanical tests
    - Sine vibration
    - Random
    - Sine on random
    - Shock
    - Free Fall
    - Bump
    - Drop Topple and stability
    - Bounce
    - Static load
    - Compression
    - Bending
    - Combined vibration and temperature
  • Mechanical testing equipment
    - Electrodynamic vibrators with slip tables 31 kN and 35,6 (nominal force sine), 1-   3000 Hz, max. amplitude 112g, velocity 1.8m/s, displacement  ± 0,5-1,5" 
    - Shock test machine, half sine, 10-3000 g, 0.2-50 ms 
    - Fall test apparatus 
    - Equipment for mechanical operating stresses 
    - Demolition hammers: 0.5 Nm and 1.0 Nm
  • Force and torque measurements
    - Force and torque measurements under constant or variable load applied to   material samples, components, sub-assemblies, etc. An important use is check   of material or assembly strength in order to assess prod-uct or process quality.     Measurements can be performed both in our lab and in the field.
    - In house mounting of strain gauges on test samples and measurement                 equipment.
    - Impact strength test of metal and plastics test specimens at controlled                 temperature, typically according to DIN50115 or EN10045.
  • Tensile strength
    - Measurement of tensile or compression strength is used to investigate the deformation characteristics for a material or connection. 
    - Tests are typically according to DIN50125, DIN50145, ISO6892 or DS/EN10002-1.
  • Fatigue test
    - Test of mechanical fatigue strength and mechanical wear. Typical test specimens are material samples, components subassemblies or complete products. If applicable, tests are made in accordance with DIN50100. 
    - Test of fatigue resistance to internal pres-sure pulsations. Typical test specimens are: pressure vessels, valves, heat exchangers. Tests are often in accordance with UL207.
  • Corrosion test
    -   Test of materials and surface protections against corrosive environments. Both      material samples and complete products are tested. Additionally adhesive strength of coating and paint can be measured.
    -   Typically test complies with: ASTM B117, IEC 60068-2-30 ISO 60068-2-52, ISO    9227 or ASTM G85-A5.
    -   Coatings and paint are tested and analyzed according to ISO 2409.
        - Salt fog
        - SO2 test
        - H2S test
        - Condensation test

  • Seal test (IP test)
    - IP tests
    - Immersion in water
    - Drip test
    - Dust test with/without vacuum
  • Other environmental tests
    - Simulated sun test
    - Height simulation
    - Overpressure
    - Rapid decompression
    - Combined temperature, moisture and height simulation
  • Acoustics, noise and vibration test and measurement campaigns
    - Accredited noise measurement against harmonized European standard IEC- 61400-11.
    - Accredited noise measurements against Danish Environmental Protection Agency’s Statutory Orders and guidelines. 
  • On-site testing and trouble shooting in case you encounter issues related to EMC, reliability or noise.
 

New accurate tool for cost calculation

Click here to try the Megavind LCOE model, which uses the same calculation methods as leaders in the offshore wind industry.

  • Publications

    Every Megavind publication released, available in one place

  • Contact

    Need Megavind materials sent to you? Contact the secretariat

  • About Megavind

    Learn more about the values and vision of Megavind

  • Events

    Make sure you do not miss any of our upcoming events